Prefab Countertops vs. Slabs: Sizes, Edges and How to Choose

Prefabricated marble countertop with a finished edge displayed horizontally beside a full upright stone slab.

If you are replacing a kitchen or bathroom countertop, you have two ways to buy the stone: a prefab (prefabricated) countertop or a full slab. Both end up as a stone top on your cabinets. The difference is how much of the work is already done when you buy it.

What is a prefab countertop?

A prefab countertop is a piece of stone that has already been cut to a standard countertop depth, with the visible edges shaped and polished. Your fabricator or installer only has to cut it to length, make the sink and cooktop cutouts, and set it in place. Because the edge work is already done, a prefab top usually takes less fabrication than a slab.

At Marble Bros, our prefab countertops come in marble and granite.

Prefab countertop sizes

For cabinets along a wall: 26 x 110 inches

This is the standard size for a run of kitchen cabinets or a bathroom vanity. It is made to fit standard 24 inch deep kitchen cabinets, and it also works on 22 inch deep bathroom vanity cabinets.

  • One long side and one short side are finished.
  • It comes with a matching 6 x 110 inch backsplash strip.

For islands and peninsulas: 36, 42 and 52 x 110 inches

These wider pieces are made for kitchen islands and peninsulas, where the countertop is seen from every side.

  • Available in 36 x 110, 42 x 110 and 52 x 110 inches.
  • All four sides are finished.

Edge choices: bullnose or square

Finished edges come either bullnosed (rounded) or square. Lately most of our customers choose the square edge, because it gives a cleaner, more modern look. Bullnose suits traditional kitchens.

What is a slab?

A slab is a full sheet of stone or porcelain with raw edges. A fabricator cuts your whole countertop out of it and then shapes and polishes every edge. We stock natural stone and porcelain slabs at our North Hollywood yard.

Prefab or slab: how to choose

A prefab countertop is usually the better fit when:

  • Your cabinets are a standard depth and run in straight lines.
  • Each run is 110 inches (9 feet 2 inches) or shorter, or you are fine with a seam on longer runs.
  • Your island is 52 inches wide or less.
  • You want to keep fabrication simple: a rental, a flip, a bathroom vanity, a laundry room or an outdoor kitchen.

A slab is usually the better fit when:

  • Your island is larger than 52 x 110 inches, or you want it in one piece.
  • You want a waterfall end, a full-height stone backsplash or a special edge shape.
  • Your layout has curves, angles or unusual depths.
  • You want porcelain, or a particular stone that is not offered as prefab.
  • You want the veining to line up across seams.

How to measure before you come in

  1. Measure the length of each cabinet run along the wall, and note the cabinet depth.
  2. Measure the island or peninsula: length and width, including any overhang for seating.
  3. Mark where the sink, cooktop and any seams would go.
  4. Bring a simple sketch with these numbers, or send it with your quote request.

We can tell you how many prefab pieces your kitchen needs, or whether a slab makes more sense.

See them in person

Stone is natural, so every piece is a little different. The best way to choose is to see the actual tops and slabs. Visit our showroom at 12537 Sherman Way, North Hollywood, CA 91605 (Monday to Friday 8am to 5pm, Saturday 8am to 4pm), call (818) 255-1200, or request a quote. Countertops and slabs are pickup only at the showroom, and your fabricator can pick up for you. See our countertops page for more.